Difference between revisions of "Orange Pi 5 detail"

From Wiki-Orange Pi
Jump to: navigation, search
(→‎26pin 的 SPI 测试)
(→‎26pin's SPI test)
 
(9 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
== How to use Win32Diskimager to burn Linux image ==
+
== '''How to use Win32Diskimager to burn Linux image''' ==
 
1) First prepare a TF card with a capacity of 16GB or more. The transmission speed of the TF card must be class 10 or above. It is recommended to use a TF card of SanDiskand other brands<br><br>
 
1) First prepare a TF card with a capacity of 16GB or more. The transmission speed of the TF card must be class 10 or above. It is recommended to use a TF card of SanDiskand other brands<br><br>
 
2) Then use the card reader to insert the TF card into the computer<br><br>
 
2) Then use the card reader to insert the TF card into the computer<br><br>
Line 23: Line 23:
 
c. After the image writing is completed, click the "Exit" button to exit, and then you can pull out the TF card and insert it into the development board to start<br><br>
 
c. After the image writing is completed, click the "Exit" button to exit, and then you can pull out the TF card and insert it into the development board to start<br><br>
  
−
== Linux system instructions ==
+
== '''Linux system instructions''' ==
 
=== Supported Linux image types and kernel versions ===
 
=== Supported Linux image types and kernel versions ===
 
{| class="wikitable"  style="width:800px;"
 
{| class="wikitable"  style="width:800px;"
Line 391: Line 391:
 
LMP Version: 5.1 (0xa) Subversion: 0x1111 Manufacturer: Broadcom Corporation (15)
 
LMP Version: 5.1 (0xa) Subversion: 0x1111 Manufacturer: Broadcom Corporation (15)
 
|}
 
|}
−
5) For the wifi connection and test method, please refer to the section of WIFI connection test, which will not be repeated here<br><br>
+
5) For the wifi connection and test method, please refer to <span style="color:#0066CC;">[[Orange Pi 5 detail#WIFI connection test | the section of WIFI connection test]]</span>, which will not be repeated here<br><br>
 
6) For the test method of Bluetooth, please refer to the section on Bluetooth usage, so I won’t go into details here<br><br>
 
6) For the test method of Bluetooth, please refer to the section on Bluetooth usage, so I won’t go into details here<br><br>
  
Line 656: Line 656:
 
|orangepi@orangepi:~$ '''dmesg'''
 
|orangepi@orangepi:~$ '''dmesg'''
 
|}
 
|}
−
4) Then you can see the device node of RTL8723BU WIFI through the '''sudo ifconfig''' command. For the connection and test method of WIFI, please refer to '''the section of WIFI connection test''', which will not be repeated here<br>
+
4) Then you can see the device node of RTL8723BU WIFI through the '''sudo ifconfig''' command. For the connection and test method of WIFI, please refer to <span style="color:#0066CC;">[[Orange Pi 5 detail#WIFI connection test | the section of WIFI connection test]]</span>, which will not be repeated here<br>
 
{| class="wikitable" style="width:800px;"  
 
{| class="wikitable" style="width:800px;"  
 
|-
 
|-
Line 941: Line 941:
 
3) There are a total of 17 GPIO ports in the 26pin interface, and the voltage of all GPIO ports is '''<span style="color:#FF0000">3.3v</span>'''<br><br>
 
3) There are a total of 17 GPIO ports in the 26pin interface, and the voltage of all GPIO ports is '''<span style="color:#FF0000">3.3v</span>'''<br><br>
  
−
== Instructions for the use of the android 12 system ==
+
== '''Instructions for the use of the android 12 system''' ==
 
=== How to use the use of wireless network card ===
 
=== How to use the use of wireless network card ===
 
1) At present, the USB wireless network card model that is adapted to the image is shown below：<br>
 
1) At present, the USB wireless network card model that is adapted to the image is shown below：<br>
Line 981: Line 981:
 
1) First click the Wiringop icon to open the Wiringop App<br><br>
 
1) First click the Wiringop icon to open the Wiringop App<br><br>
 
[[Image:Pi-5-details2-pic32.png]]<br><br>
 
[[Image:Pi-5-details2-pic32.png]]<br><br>
−
2) The main interface of the Wiringop app is displayed as shown in the figure below, and then click the GPIO_TEST button to open the GPIO test interface<br><br>
+
2) The main interface of the Wiringop app is displayed as shown in the figure below, and then click the '''GPIO_TEST''' button to open the GPIO test interface<br><br>
 
[[Image:Pi-5-details2-pic33.png]]<br><br>
 
[[Image:Pi-5-details2-pic33.png]]<br><br>
−
3) The GPIO test interface is shown in the figure below. The two rows of the CheckBox button on the left and the 26PIN pin are one -to -one relationship. When checking the CheckBox button, the corresponding pin will be set to OUT mode, the pin level settings will be set. For high levels, when the check -up is canceled, the pin level is set to a low level; when clicking the GPIO READALL button on the right, you can get the WPI, GPIO mode, pin level information, etc.<br><br>
+
3) The GPIO test interface is shown in the figure below. The two rows of the '''CheckBox''' button on the left and the 26PIN pin are one -to -one relationship. When checking the '''CheckBox''' button, the corresponding pin will be set to '''OUT''' mode, the pin level settings will be set. For high levels, when the check -up is canceled, the pin level is set to a low level; when clicking the '''GPIO READALL''' button on the right, you can get the WPI, GPIO mode, pin level information, etc.<br><br>
 
[[Image:Pi-5-details2-pic34.png]]<br><br>
 
[[Image:Pi-5-details2-pic34.png]]<br><br>
−
4) Then click the GPIO READALL button, and the output information is shown in the figure below<br><br>
+
4) Then click the '''GPIO READALL''' button, and the output information is shown in the figure below<br><br>
 
[[Image:Pi-5-details2-pic35.png]]<br><br>
 
[[Image:Pi-5-details2-pic35.png]]<br><br>
−
5) Taking the high and low level of the GPIO2_D4 as an example, click the CheckBox button in the figure below. When the button is selected, the GPIO2_D4 is set to a high level. After setting, you can use the value of the voltage of the pins by the multimeter. If it is 3.3v, Explain that setting high -electricity is successful<br><br>
+
5) Taking the high and low level of the '''GPIO2_D4''' as an example, click the '''CheckBox''' button in the figure below. When the button is selected, the '''GPIO2_D4''' is set to a high level. After setting, you can use the value of the voltage of the pins by the multimeter. If it is '''3.3v''', Explain that setting high -electricity is successful<br><br>
 
[[Image:Pi-5-details2-pic36.png]]<br><br>
 
[[Image:Pi-5-details2-pic36.png]]<br><br>
−
6) Then click the GPIO READALL button to see that the pins mode of the current GPIO2_D4 is OUT, and the pin level is high level<br><br>
+
6) Then click the '''GPIO READALL''' button to see that the pins mode of the current '''GPIO2_D4''' is '''OUT''', and the pin level is high level<br><br>
 
[[Image:Pi-5-details2-pic37.png]]<br><br>
 
[[Image:Pi-5-details2-pic37.png]]<br><br>
−
7) Click the CheckBox button in the figure below to cancel the check status. The GPIO2_D4 pin is set to a low level. After setting, you can use the value of the voltage of the multimeter to measure the pins.If it is 0v, the low -power flat is set.<br><br>
+
7) Click the '''CheckBox''' button in the figure below to cancel the check status. The '''GPIO2_D4''' pin is set to a low level. After setting, you can use the value of the voltage of the multimeter to measure the pins.If it is '''0v''', the low -power flat is set.<br><br>
 
[[Image:Pi-5-details2-pic38.png]]<br><br>
 
[[Image:Pi-5-details2-pic38.png]]<br><br>
−
8) Then click the GPIO READALL button to see that the pins mode of the current GPIO2_D4 is OUT, and the pin level is low<br><br>
+
8) Then click the '''GPIO READALL''' button to see that the pins mode of the current GPIO2_D4 is OUT, and the pin level is low<br><br>
 
[[Image:Pi-5-details2-pic39.png]]<br><br>
 
[[Image:Pi-5-details2-pic39.png]]<br><br>
  
Line 1,001: Line 1,001:
 
2) First click the WiringOP icon to open the Wiringop App<br><br>
 
2) First click the WiringOP icon to open the Wiringop App<br><br>
 
[[Image:Pi-5-details2-pic41.png]]<br><br>
 
[[Image:Pi-5-details2-pic41.png]]<br><br>
−
3) The main interface of the WiringOP APP is displayed as shown in the figure below, and then click the UART_TEST button to open the UART test interface<br><br>
+
3) The main interface of the WiringOP APP is displayed as shown in the figure below, and then click the '''UART_TEST''' button to open the UART test interface<br><br>
 
[[Image:Pi-5-details2-pic42.png]]<br><br>
 
[[Image:Pi-5-details2-pic42.png]]<br><br>
 
4) The serial test interface of the APP is shown in the figure below<br><br>
 
4) The serial test interface of the APP is shown in the figure below<br><br>
 
[[Image:Pi-5-details2-pic43.png]]<br><br>
 
[[Image:Pi-5-details2-pic43.png]]<br><br>
−
5) Then enter the baud rate you want to set in the editing box, and then click the OPEN button to open the/dev/ttyS0 node. After successful, the OPEN button becomes an optional state.The CLOSE button and the SEND button become an optional state<br><br>
+
5) Then enter the baud rate you want to set in the editing box, and then click the '''OPEN''' button to open the '''/dev/ttyS0''' node. After successful, the '''OPEN''' button becomes an optional state.The '''CLOSE''' button and the '''SEND''' button become an optional state<br><br>
 
[[Image:Pi-5-details2-pic44.png]]<br><br>
 
[[Image:Pi-5-details2-pic44.png]]<br><br>
 
6) Then use the DuPont line to shorte the RXD and TXD pin of uart0<br><br>
 
6) Then use the DuPont line to shorte the RXD and TXD pin of uart0<br><br>
 
[[Image:Pi-5-details2-pic45.png]]<br><br>
 
[[Image:Pi-5-details2-pic45.png]]<br><br>
−
7) Then you can enter a section of characters in the editing box below, click the SEND button to start sending<br><br>
+
7) Then you can enter a section of characters in the editing box below, click the '''SEND''' button to start sending<br><br>
 
[[Image:Pi-5-details2-pic46.png]]<br><br>
 
[[Image:Pi-5-details2-pic46.png]]<br><br>
 
8) If everything is normal, the receiving string will be displayed in the receiving box<br><br>
 
8) If everything is normal, the receiving string will be displayed in the receiving box<br><br>
 
[[Image:Pi-5-details2-pic47.png]]<br><br>
 
[[Image:Pi-5-details2-pic47.png]]<br><br>
  
−
=== 26pin's SPI test ===
+
=== 26pin's PWM test ===
−
1) From the schematic diagram of the 26pin interface, the SPI available for Orange Pi 5 is spi4<br><br>
+
1) Android only opened '''PWM15''' by default. The corresponding pins are at the position of 26Pin.<br><br>
 
[[Image:Pi-5-details2-pic48.png]]<br><br>
 
[[Image:Pi-5-details2-pic48.png]]<br><br>
−
2) Here is the w25q64 module to test the SPI interface, and first access the w25q64 device at the SPI4 interface.<br><br>
+
2) First click theWiringOP icon to open the Wiringop App<br><br>
 
[[Image:Pi-5-details2-pic49.png]]<br><br>
 
[[Image:Pi-5-details2-pic49.png]]<br><br>
−
3) Then click the WiringOP icon to open the WiringOP APP<br><br>
+
3) Then click the '''PWM_TEST''' button to enter the PWM test interface at the main interface of WiringOP<br><br>
 
[[Image:Pi-5-details2-pic50.png]]<br><br>
 
[[Image:Pi-5-details2-pic50.png]]<br><br>
−
4) The main interface of the WiringOP APP shows as shown in the figure below, click the SPI_TEST button to open the SPI test interface<br><br>
+
4) The corresponding address corresponding to the PWM15 is '''febf0030'''. The right side of PWMCHIP0 is exactly the '''febf0030.pwm'''. If the displayed base address is wrong, please click the drop -down option to select other PWMCHIP until the '''febf0030''' is displayed on the right.<br><br>
 
[[Image:Pi-5-details2-pic51.png]]<br><br>
 
[[Image:Pi-5-details2-pic51.png]]<br><br>
−
5) Then click the OPEN button to initialize SPI<br><br>
+
5) Then confirm the PWM cycle. The default configuration is '''50000ns''', and the PWM frequency is '''20KHz'''. You can modify it by yourself.Click on the button to export '''PWM15'''<br><br>
 
[[Image:Pi-5-details2-pic52.png]]<br><br>
 
[[Image:Pi-5-details2-pic52.png]]<br><br>
−
6) Then fill in bytes that need to be sent, such as reading the ID information of W25Q64, fill in the address 0x9F in data [0], and then click the TRANSFER button<br><br>
+
6) Then drag the drag below to change the PWM duty ratio, and then check the enable to output PWM<br><br>
 
[[Image:Pi-5-details2-pic53.png]]<br><br>
 
[[Image:Pi-5-details2-pic53.png]]<br><br>
−
7) The last app will display the ID information read<br><br>
 
 
[[Image:Pi-5-details2-pic54.png]]<br><br>
 
[[Image:Pi-5-details2-pic54.png]]<br><br>
−
8) The MANUFACTURER ID of the w25q64 module is EFh, the Device ID is 4017h, and the value read above is corresponding (H represents hexadecimal)<br><br>
+
 
 +
=== 26pin's SPI test ===
 +
1) From the schematic diagram of the 26pin interface, the SPI available for Orange Pi 5 is spi4<br><br>
 
[[Image:Pi-5-details2-pic55.png]]<br><br>
 
[[Image:Pi-5-details2-pic55.png]]<br><br>
−
 
+
2) Here is the w25q64 module to test the SPI interface, and first access the w25q64 device at the SPI4 interface.<br><br>
−
=== 26pin 的 PWM 测试 ===
 
−
1) Android only opened PWM15 by default. The corresponding pins are at the position of 26Pin.<br><br>
 
 
[[Image:Pi-5-details2-pic56.png]]<br><br>
 
[[Image:Pi-5-details2-pic56.png]]<br><br>
−
2) First click theWiringOP icon to open the Wiringop App<br><br>
+
3) Then click the WiringOP icon to open the WiringOP APP<br><br>
 
[[Image:Pi-5-details2-pic57.png]]<br><br>
 
[[Image:Pi-5-details2-pic57.png]]<br><br>
−
3) Then click the PWM_TEST button to enter the PWM test interface at the main interface of WiringOP<br><br>
+
4) The main interface of the WiringOP APP shows as shown in the figure below, click the SPI_TEST button to open the SPI test interface<br><br>
 
[[Image:Pi-5-details2-pic58.png]]<br><br>
 
[[Image:Pi-5-details2-pic58.png]]<br><br>
−
4) The corresponding address corresponding to the PWM15 is febf0030. The right side of PWMCHIP0 is exactly the febf0030.pwm. If the displayed base address is wrong, please click the drop -down option to select other PWMCHIP until the febf0030 is displayed on the right.<br><br>
+
5) Then click the '''OPEN''' button to initialize SPI<br><br>
 
[[Image:Pi-5-details2-pic59.png]]<br><br>
 
[[Image:Pi-5-details2-pic59.png]]<br><br>
−
5) Then confirm the PWM cycle. The default configuration is 50000ns, and the PWM frequency is 20KHz. You can modify it by yourself.Click on the button to export PWM15<br><br>
+
6) Then fill in bytes that need to be sent, such as reading the ID information of W25Q64, fill in the address 0x9F in data [0], and then click the '''TRANSFER''' button<br><br>
 
[[Image:Pi-5-details2-pic60.png]]<br><br>
 
[[Image:Pi-5-details2-pic60.png]]<br><br>
−
6) Then drag the drag below to change the PWM duty ratio, and then check the enable to output PWM<br><br>
+
7) The last app will display the ID information read<br><br>
 
[[Image:Pi-5-details2-pic61.png]]<br><br>
 
[[Image:Pi-5-details2-pic61.png]]<br><br>
 +
8) The MANUFACTURER ID of the w25q64 module is EFh, the Device ID is 4017h, and the value read above is corresponding (H represents hexadecimal)<br><br>
 +
[[Image:Pi-5-details2-pic62.png]]<br><br>

Latest revision as of 09:50, 24 April 2023

How to use Win32Diskimager to burn Linux image

1) First prepare a TF card with a capacity of 16GB or more. The transmission speed of the TF card must be class 10 or above. It is recommended to use a TF card of SanDiskand other brands

2) Then use the card reader to insert the TF card into the computer

3) Then format the TF card
a. SD Card Formatter can be used to format the TF card. The download address is:

https://www.sdcard.org/downloads/formatter/eula_windows/SDCardFormatterv5_WinEN.zip

b. After downloading, unzip and install directly, and then open the software

c. If only a TF card is inserted into the computer, the drive letter of the TF card will be displayed in the "Select card" column. If multiple USB storage devices are inserted into the computer, you can select the corresponding drive letter of the TF card through the drop-down box

Pi-5-details-pic55.png

d. Then click "Format", a warning box will pop up before formatting, and formatting will start after selecting "Yes (Y)"

Pi-5-details-pic56.png

e. After formatting the TF card, the information shown in the figure below will pop up, click OK

Pi-5-details-pic57.png

4) Download the Linux operating system image file compression package that you want to burn from the Orange Pi data download page, and then use the decompression software to decompress it. Among the decompressed files, the file ending with ".img" is the image file of the operating system. The size is generally more than 2GB

5) Use Win32Diskimager to burn the Linux image to the TF card
a. The download page of Win32Diskimager is

http://sourceforge.net/projects/win32diskimager/files/Archive/

b. After downloading, install it directly. The interface of Win32Diskimager is as follows
a) First select the path of the image file
b) Then confirm that the drive letter of the TF card is consistent with that displayed in the "Device" column
c) Finally click "Write" to start burning

Pi-5-details-pic58.png

c. After the image writing is completed, click the "Exit" button to exit, and then you can pull out the TF card and insert it into the development board to start

Linux system instructions

Supported Linux image types and kernel versions

Linux image type kernel version server version desktop version
Debian 11 - Bullseye Linux5.10 support support
Ubuntu 20.04 - Focal Linux5.10 support support
Ubuntu 22.04 - Jammy Linux5.10 support support

Onboard LED Light Test Instructions

1) There are two LED lights on the development board, one is green and the other is red. The location is shown in the figure below:

Pi-5-details-pic59.png

2) As long as the development board is powered on, the red LED light will always be on, which is controlled by the hardware and cannot be turned off by the software.

3) The green LED light will keep flashing after the kernel is started, which is controlled by software.

4) The method of setting the green light on and off and flashing is as follows


Note that the following operations should be performed under the root user.

a. First enter the setting directory of the green light

root@orangepi:~# cd /sys/class/leds/status_led

b. The command to set the green light to stop flashing is as follows

root@orangepi:/sys/class/leds/status_led# echo none > trigger

c. The command to set the green light to be on is as follows

root@orangepi:/sys/class/leds/status_led# echo 1 > brightness

d. The command to set the green light to flash is as follows

root@orangepi:/sys/class/leds/status_led# echo heartbeat > trigger

Ethernet port test

1) First, insert one end of the network cable into the Ethernet interface of the development board, and connect the other end of the network cable to the router, and ensure that the network is unblocked

2) After the system starts, it will automatically assign an IP address to the Ethernet card through DHCP，No other configuration is required

3) The command to view the IP address in the Linux system of the development board is as follows

orangepi@orangepi:~$ ip addr show eth0

2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 4a:fe:2b:3d:17:1c brd ff:ff:ff:ff:ff:ff
inet 192.168.1.150/24 brd 192.168.1.255 scope global dynamic noprefixroute eth0 valid_lft 43150sec preferred_lft 43150sec
inet6 fe80::9a04:3703:faed:23be/64 scope link noprefixroute

When using ifconfig to view the IP address, if the following information is displayed, it is because sudo is not added. The correct command is：sudo ifconfig

Command 'ifconfig' is available in the following places
/sbin/ifconfig
/usr/sbin/ifconfig
The command could not be located because '/sbin:/usr/sbin' is not included in the PATH environment variable.
This is most likely caused by the lack of administrative privileges associated with your user account.
ifconfig: command not found

There are three ways to check the IP address after the development board starts:

1. Connect the HDMI monitor, then log in to the system and use the ip addr show eth0 command to view the IP address
2. Enter the ip addr show eth0 command in the debugging serial terminal to view the IP address
3. If there is no debugging serial port and no HDMI display, you can also check the IP address of the development board's network port through the router's management interface. However, in this method, some people often cannot see the IP address of the development board normally. If you can't see it, the debug method looks like this:
A) First check whether the Linux system has started normally. If the green light of the development board is blinking, it is generally started normally. If only the red light is on, it means that the system has not started normally;
B) Check whether the network cable is plugged in tightly, or try another network cable;
C) Try another router (I have encountered many problems with the router, such as the router cannot assign the IP address normally, or the IP address has been assigned normally but cannot be seen in the router);
D) If there is no router to replace, you can only connect to an HDMI display or use the debugging serial port to check the IP address.

In addition, it should be noted that the development board DHCP automatically assigns an IP address without any settings.

4) The command to test the network connectivity is as follows, the ping command can be interrupted through the shortcut key of Ctrl+C

orangepi@orangepi:~$ ping www.baidu.com -I eth0

PING www.a.shifen.com (14.215.177.38) from 192.168.1.12 eth0: 56(84) bytes of data.
64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=1 ttl=56 time=6.74 ms
64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=2 ttl=56 time=6.80 ms
64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=3 ttl=56 time=6.26 ms
64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=4 ttl=56 time=7.27 ms
^C
--- www.a.shifen.com ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3002ms
rtt min/avg/max/mdev = 6.260/6.770/7.275/0.373 ms


WIFI connection test

Please do not connect to WIFI by modifying the /etc/network/interfaces configuration file. There will be problems connecting to the WIFI network in this way.

1. The server image connects to WIFI through commands

When the development board is not connected to Ethernet, not connected to HDMI display, but only connected to the serial port, it is recommended to use the commands demonstrated in this section to connect to the WIFI network. Because nmtui can only display characters in some serial port software (such as minicom), and cannot display the graphical interface normally. Of course, if the development board is connected to an Ethernet or HDMI display, you can also use the commands demonstrated in this section to connect to the WIFI network.

1) First log in to the linux system, there are the following three ways
a. If the development board is connected with a network cable, you can remotely log in to the Linux system through ssh
b. If the development board is connected to the debugging serial port, you can use the serial port terminal to log in to the Linux system
c. If the development board is connected to the HDMI display, you can log in to the linux system through the terminal displayed on the HDMI

2) First use the nmcli dev wifi command to scan the surrounding WIFI hotspots

orangepi@orangepi:~$ nmcli dev wifi

Pi-5-details-pic60.png

3) Then use the nmcli command to connect to the scanned WIFI hotspot, where：
a. wifi_name needs to be replaced with the name of the WIFI hotspot you want to connect to
b. wifi_passwd needs to be replaced with the password of the WIFI hotspot you want to connect to

orangepi@orangepi:~$ nmcli dev wifi connect wifi_name password wifi_passwd

Device 'wlan0' successfully activated with 'cf937f88-ca1e-4411-bb50-61f402eef293'.

4) You can view the IP address of wifi through the ip addr show wlan0 command

orangepi@orangepi:~$ ip addr show wlan0

11: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 23:8c:d6:ae:76:bb brd ff:ff:ff:ff:ff:ff
inet 192.168.1.11/24 brd 192.168.1.255 scope global dynamic noprefixroute wlan0 valid_lft 259192sec preferred_lft 259192sec
inet6 240e:3b7:3240:c3a0:c401:a445:5002:ccdd/64 scope global dynamic noprefixroute
valid_lft 259192sec preferred_lft 172792sec
inet6 fe80::42f1:6019:a80e:4c31/64 scope link noprefixroute valid_lft forever preferred_lft forever

5) Use the ping command to test the connectivity of the wifi network, and the ping command can be interrupted through the shortcut key Ctrl+C

orangepi@orangepi:~$ ping www.orangepi.online -I wlan0

PING www.orangepi.online (182.92.236.130) from 192.168.1.49 wlan0: 56(84) bytes of data.
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=1 ttl=52 time=43.5 ms
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=2 ttl=52 time=41.3 ms
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=3 ttl=52 time=44.9 ms
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=4 ttl=52 time=45.6 ms
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=5 ttl=52 time=48.8 ms
^C
--- www.orangepi.online ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4006ms rtt min/avg/max/mdev = 41.321/44.864/48.834/2.484 ms

2. The server image connects to WIFI in a graphical way

1) First log in to the linux system, there are the following three ways
a. If the development board is connected with a network cable, you can remotely log in to the Linux system through ssh
b. If the development board is connected to the debugging serial port, you can use the serial port terminal to log in to the linux system (please use MobaXterm for the serial port software, and minicom cannot display the graphical interface)
c. If the development board is connected to the HDMI display, you can log in to the linux system through the terminal displayed on the HDMI

2) Then enter the nmtui command in the command line to open the wifi connection interface

orangepi@orangepi:~$ nmtui

3) Enter the nmtui command to open the interface as shown below

Pi-5-details-pic61.png

4) Select Activate a connect and press Enter

Pi-5-details-pic62.png

5) Then you can see all the searched WIFI hotspots

Pi-5-details-pic63.png

6) Select the WIFI hotspot you want to connect to, then use the Tab key to position the cursor on Activate and press Enter

Pi-5-details-pic64.png

7) Then a dialog box for entering a password will pop up, enter the corresponding password in Password and press Enter to start connecting to WIFI

Pi-5-details-pic65.png

8) After the WIFI connection is successful, a "*" will be displayed in front of the connected WIFI name

Pi-5-details-pic66.png

9) You can view the IP address of wifi through the ip addr show wlan0 command

orangepi@orangepi:~$ ip addr show wlan0

11: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 24:8c:d3:aa:76:bb brd ff:ff:ff:ff:ff:ff
inet 192.168.1.11/24 brd 192.168.1.255 scope global dynamic noprefixroute wlan0 valid_lft 259069sec preferred_lft 259069sec
inet6 240e:3b7:3240:c4a0:c401:a445:5002:ccdd/64 scope global dynamic noprefixroute
valid_lft 259071sec preferred_lft 172671sec
inet6 fe80::42f1:6019:a80e:4c31/64 scope link noprefixroute valid_lft forever preferred_lft forever

10) Use the ping command to test the connectivity of the wifi network, and the ping command can be interrupted through the shortcut key Ctrl+C

orangepi@orangepi:~$ ping www.orangepi.online -I wlan0

PING www.orangepi.online (182.92.236.130) from 192.168.1.49 wlan0: 56(84) bytes of data.
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=1 ttl=52 time=43.5 ms
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=2 ttl=52 time=41.3 ms
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=3 ttl=52 time=44.9 ms
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=4 ttl=52 time=45.6 ms
64 bytes from 182.92.236.130 (182.92.236.130): icmp_seq=5 ttl=52 time=48.8 ms
^C
--- www.orangepi.online ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4006ms rtt min/avg/max/mdev = 41.321/44.864/48.834/2.484 ms

3. Test method of desktop image

1) Click the network configuration icon in the upper right corner of the desktop (please do not connect the network cable when testing WIFI)

Pi-5-details-pic67.png

2) Click More networks in the pop-up drop-down box to see all scanned WIFI hotspots, and then select the WIFI hotspot you want to connect to

Pi-5-details-pic68.png

3) Then enter the password of the WIFI hotspot, and then click Connect to start connecting to WIFI

Pi-5-details-pic69.png

4) After connecting to WIFI, you can open the browser to check whether you can access the Internet. The entrance of the browser is shown in the figure below

Pi-5-details-pic70.png

5) If you can open other web pages after opening the browser, it means that the WIFI connection is normal

Pi-5-details-pic71.png

How to set a static IP address


1.Use the nmtui command to set a static IP address

1) First run the nmtui command

orangepi@orangepi:~$ nmtui

2) Then select Edit a connection and press Enter

Pi-5-details-pic72.png

3) Then select the network interface that needs to set a static IP address, for example, to set the static IP address of the Ethernet interface, select Wired connection 1

Pi-5-details-pic73.png

4) Then select Edit via the Tab key and press the Enter key

Pi-5-details-pic74.png

5) Then use the Tab key to move the cursor to the <Automatic> position shown in the figure below to configure IPv4

Pi-5-details-pic75.png

6) Then press Enter, select Manual through the up and down arrow keys, and press Enter to confirm

Pi-5-details-pic76.png

7) The display after selection is shown in the figure below

Pi-5-details-pic77.png

8) Then move the cursor to <Show> via the Tab key

Pi-5-details-pic78.png

9) Then press Enter, and the following setting interface will pop up after entering

Pi-5-details-pic79.png

10) Then you can set the IP address (Addresses), gateway (Gateway) and DNS server address in the position shown in the figure below (there are many other setting options in it, please explore by yourself)，Please set it according to your specific needs, the value set in the figure below is just an example

Pi-5-details-pic80.png

11) After setting, move the cursor to <OK> in the lower right corner, and press Enter to confirm

Pi-5-details-pic81.png

12) Then click <Back> to return to the previous selection interface

Pi-5-details-pic82.png

13) Then select Activate a connection, then move the cursor to <OK>, and finally click Enter

Pi-5-details-pic83.png

14) Then select the network interface that needs to be set, such as Wired connection 1, then move the cursor to <Deactivate>, and press Enter to disable Wired connection 1

Pi-5-details-pic84.png

15) Then please do not move the cursor, and then press the Enter key to re-enable Wired connection 1, so that the static IP address set earlier will take effect

Pi-5-details-pic85.png

16) Then you can exit nmtui through the <Back> and Quit buttons

Pi-5-details-pic86.pngPi-5-details-pic86-1.png

17) Then through ip addr show eth0, you can see that the IP address of the network port has changed to the static IP address set earlier

orangepi@orangepi:~$ ip addr show eth0

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 5e:ac:14:a5:92:b3 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.177/24 brd 192.168.1.255 scope global noprefixroute eth0 valid_lft forever preferred_lft forever
inet6 241e:3b8:3240:c3a0:e269:8305:dc08:135e/64 scope global dynamic noprefixroute
valid_lft 259149sec preferred_lft 172749sec
inet6 fe80::957d:bbbe:4928:3604/64 scope link noprefixroute valid_lft forever preferred_lft forever

18) Then you can test the connectivity of the network to check whether the IP address is configured OK, and the ping command can be interrupted through the shortcut key Ctrl+C

orangepi@orangepi:~$ ping 192.168.1.47 -I eth0

PING 192.168.1.47 (192.168.1.47) from 192.168.1.188 eth0: 56(84) bytes of data.
64 bytes from 192.168.1.47: icmp_seq=1 ttl=64 time=0.233 ms
64 bytes from 192.168.1.47: icmp_seq=2 ttl=64 time=0.263 ms
64 bytes from 192.168.1.47: icmp_seq=3 ttl=64 time=0.273 ms
64 bytes from 192.168.1.47: icmp_seq=4 ttl=64 time=0.269 ms
64 bytes from 192.168.1.47: icmp_seq=5 ttl=64 time=0.275 ms


2.Use the nmcli command to set a static IP address

1) If you want to set the static IP address of the network port, please insert the network cable into the development board first. If you need to set the static IP address of WIFI, please connect the WIFI first, and then start to set the static IP address

2) Then you can view the name of the network device through the nmcli con show command, as shown below
a. orangepi is the name of the WIFI network interface (the name is not necessarily the same)
b. Wired connection 1 is the name of the Ethernet interface

orangepi@orangepi:~$ nmcli con show
NAME UUID TYPE DEVICE
orangepi cfc4f922-ae48-46f1-84e1-2f19e9ec5e2a wifi wlan0
Wired connection 1 9db058b7-7701-37b8-9411-efc2ae8bfa30 ethernet eth0

3) Then enter the following command, where
a. "Wired connection 1" means to set the static IP address of the Ethernet port. If you need to set the static IP address of the WIFI, please modify it to the corresponding name of the WIFI network interface (you can get it through the nmcli con show command)
b. ipv4.addresses is followed by the static IP address to be set, which can be modified to the value you want to set
c. ipv4.gateway represents the address of the gateway

orangepi@orangepi:~$ nmcli con mod "Wired connection 1" \

ipv4.addresses "192.168.1.110" \
ipv4.gateway "192.168.1.1" \
ipv4.dns "8.8.8.8" \
ipv4.method "manual"

4) Then restart the linux system

orangepi@orangepi:~$ sudo reboot

5) Then re-enter the linux system and use the ip addr show eth0 command to see that the IP address has been set to the desired value

orangepi@orangepi:~$ ip addr show eth0

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 5e:ae:14:a5:91:b3 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.110/32 brd 192.168.1.110 scope global noprefixroute eth0 valid_lft forever preferred_lft forever
inet6 240e:3b7:3240:c3a0:97de:1d01:b290:fe3a/64 scope global dynamic noprefixroute
valid_lft 259183sec preferred_lft 172783sec
inet6 fe80::3312:861a:a589:d3c/64 scope link noprefixroute valid_lft forever preferred_lft forever

How to use AP6275P PCIe network card

1) First, you need to purchase an AP6275P PCIe network card as shown in the figure below

Pi-5-details-pic87.png

2) Then insert the AP6275P PCIe network card into the M.2 interface of the development board and fix it

Pi-5-details-pic88.png

3) Then open the configuration of the AP6275P PCIe network card in the linux system, the steps are as follows：
a. First run orangepi-config, normal users remember to add sudo permission

orangepi@orangepi:~$ sudo orangepi-config

b. Then select System

Pi-5-details-pic89.png

c. Then select Hardware

Pi-5-details-pic90.png

d. Then use the arrow keys on the keyboard to navigate to wifi-ap6275p, and then use the space to select
Pi-5-details-pic91.png

e. Then select <Save> to save

Pi-5-details-pic92.png

f. Then select <Back>

Pi-5-details-pic93.png

g. Then select <Reboot> to restart the system to make the configuration take effect

Pi-5-details-pic94.png

The above settings will eventually add the configuration of overlays=wifi-ap6275p to /boot/orangepiEnv.txt. After setting, you can check it first. If this configuration does not exist, then there is a problem with the settings.

If you find it troublesome to use orangepi-config, you can also open /boot/orangepiEnv.txt, and then add the configuration of overlays=wifi-ap6275p.

4) If everything is normal after restarting the system, use the following command to see the device nodes of WIFI and Bluetooth
a. The command to view the WIFI device node is as follows：

orangepi@orangepi:~$ ip addr show wlan0

3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc fq_codel state DORMANT group default qlen 1000
link/ether 70:f7:54:b8:b3:17 brd ff:ff:ff:ff:ff:ff

b. The command to view the Bluetooth device node is as follows：

orangepi@orangepi:~$ hciconfig -a

hci0: Type: Primary Bus: UART
BD Address: 82:CC:AE:62:CE:3E ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING
RX bytes:958 acl:0 sco:0 events:73 errors:0
TX bytes:5544 acl:0 sco:0 commands:73 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'orangepi5'
Class: 0x1c0000
Service Classes: Rendering, Capturing, Object Transfer Device Class: Miscellaneous,
HCI Version: 5.1 (0xa) Revision: 0x3f9
LMP Version: 5.1 (0xa) Subversion: 0x1111 Manufacturer: Broadcom Corporation (15)

5) For the wifi connection and test method, please refer to the section of WIFI connection test, which will not be repeated here

6) For the test method of Bluetooth, please refer to the section on Bluetooth usage, so I won’t go into details here

AP6275P PCIe NIC creates WIFI hotspot via create_ap

create_ap is a script that helps quickly create WIFI hotspots on Linux, and supports bridge and NAT modes. It can automatically combine hostapd, dnsmasq and iptables to complete the setting of WIFI hotspots, avoiding complex configuration for users. The github address is as follows：

https://github.com/oblique/create_ap

If you using the latest image, the create_ap script has been pre-installed, and you can create a WIFI hotspot through the create_ap command. The basic command format of create_ap is as follows:

create_ap [options] <wifi-interface> [<interface-with-internet>]
[<access-point-name> [<passphrase>]]

1.create_ap method to create WIFI hotspot in NAT mode

1) Enter the following command to create a WIFI hotspot named orangepi and password orangepi in NAT mode

orangepi@orangepi5:~$ sudo create_ap -m nat wlan0 eth0 orangepi orangepi

2) If the following information is output, it means that the WIFI hotspot is created successfully

orangepi@orangepi5:~$ sudo create_ap -m nat wlan0 eth0 orangepi orangepi

Config dir: /tmp/create_ap.wlan0.conf.fPItFUJ2 PID: 3831
Network Manager found, set ap0 as unmanaged device... DONE
Creating a virtual WiFi interface... ap0 created.
Sharing Internet using method: nat
hostapd command-line interface: hostapd_cli -p
/tmp/create_ap.wlan0.conf.fPItFUJ2/hostapd_ctrl ap0: interface state UNINITIALIZED->ENABLED

3) Take out the mobile phone at this time, in the searched WIFI list, you can find the WIFI hotspot named orangepi created by the development board, and then click orangepi to connect to the hotspot, the password is the orangepi set above

Pi-5-details-pic95.png

4) After the connection is successful, the display is as shown in the figure below

Pi-5-details-pic96.png

5) In NAT mode, the wireless device connected to the hotspot of the development board requests an IP address from the DHCP service of the development board, so there will be two different network segments, for example, the IP of the development board is 192.168.1.X

orangepi@orangepi5:~$ ifconfig eth0

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.150 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::938f:8776:5783:afa2 prefixlen 64 scopeid 0x20<link>
ether 4a:a0:c8:25:42:82 txqueuelen 1000 (Ethernet)
RX packets 25370 bytes 2709590 (2.7 MB)
RX errors 0 dropped 50 overruns 0 frame 0
TX packets 3798 bytes 1519493 (1.5 MB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 83

By default, the DHCP service of the development board will assign an IP address of 192.168.12.0/24 to the device connected to the hotspot. At this time, click on the connected WIFI hotspot orangepi, and then you can see that the IP address of the mobile phone is 192.168.12.X

Pi-5-details-pic97.png

Pi-5-details-pic98.png

6) If you want to specify a different network segment for the connected device, you can specify it through the -g parameter, such as specifying the network segment of the access point AP through the -g parameter as 192.168.2.1

orangepi@orangepi5:~$ sudo create_ap -m nat wlan0 eth0 orangepi orangepi -g 192.168.2.1

At this time, after connecting to the hotspot through the mobile phone, click the connected WIFI hotspot orangepi, and then you can see that the IP address of the mobile phone is 192.168.2.X

Pi-5-details-pic99.png

Pi-5-details-pic100.png

7) If the --freq-band parameter is not specified, the hotspot created by default is in the 2.4G frequency band. If you want to create a hotspot in the 5G frequency band, you can specify it through the --freq-band 5 parameter. The specific command is as follows

orangepi@orangepi:~$ sudo create_ap -m nat wlan0 eth0 orangepi orangepi --freq-band 5

8) If you need to hide the SSID, you can specify the --hidden parameter, the specific command is as follows

orangepi@orangepi:~$ sudo create_ap -m nat wlan0 eth0 orangepi orangepi --hidden

At this time, the mobile phone cannot search for the WIFI hotspot. You need to manually specify the name of the WIFI hotspot and enter the password to connect to the WIFI hotspot

Pi-5-details-pic101.png

2.create_ap method to create WIFI hotspot in bridge mode

1) Enter the following command to create a WIFI hotspot named orangepi and password orangepi in bridge mode

orangepi@orangepi:~$ sudo create_ap -m bridge wlan0 eth0 orangepi orangepi

2) If the following information is output, it means that the WIFI hotspot is created successfully

orangepi@orangepi:~$ sudo create_ap -m bridge wlan0 eth0 orangepi orangepi

[sudo] password for orangepi:
Config dir: /tmp/create_ap.wlan0.conf.fg9U5Xgt
PID: 3141
Network Manager found, set ap0 as unmanaged device... DONE
Creating a virtual WiFi interface... ap0 created.
Sharing Internet using method: bridge
Create a bridge interface... br0 created.
hostapd command-line interface: hostapd_cli -p
/tmp/create_ap.wlan0.conf.fg9U5Xgt/hostapd_ctrl
ap0: interface state UNINITIALIZED->ENABLED ap0: AP-ENABLED

3) Take out the mobile phone at this time, and you can find the WIFI hotspot named orangepi created by the development board in the searched WIFI list, and then you can click orangepi to connect to the hotspot, and the password is the orangepi set above

Pi-5-details-pic102.png

4) After the connection is successful, the display is as shown in the figure below

Pi-5-details-pic103.png

5) In bridge mode, the wireless device connected to the hotspot of the development board also requests an IP address from the DHCP service of the main router (the router connected to the development board), for example, the IP of the development board is 192.168.1.X

orangepi@orangepi:~$ ifconfig eth0

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.150 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::938f:8776:5783:afa2 prefixlen 64 scopeid 0x20<link>
ether 4a:a0:c8:25:42:82 txqueuelen 1000 (Ethernet)
RX packets 25370 bytes 2709590 (2.7 MB)
RX errors 0 dropped 50 overruns 0 frame 0
TX packets 3798 bytes 1519493 (1.5 MB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 83

The IP of the device connected to the WIFI hotspot is also assigned by the main router, so the mobile phone connected to the WIFI hotspot and the development board are in the same network segment. At this time, click on the connected WIFI hotspot orangepi, and then you can see the IP address of the mobile phone Also 192.168.1.X

Pi-5-details-pic104.png

Pi-5-details-pic105.png

6) If the --freq-band parameter is not specified, the hotspot created by default is in the 2.4G frequency band. If you want to create a hotspot in the 5G frequency band, you can specify the --freq-band 5 parameter. The specific command is as follows

orangepi@orangepi:~$ sudo create_ap -m bridge wlan0 eth0 orangepi orangepi --freq-band 5

7) If you need to hide the SSID, you can specify the --hidden parameter, the specific command is as follows

orangepi@orangepi:~$ sudo create_ap -m bridge wlan0 eth0 orangepi orangepi --hidden

At this time, the mobile phone cannot search for the WIFI hotspot. You need to manually specify the name of the WIFI hotspot and enter the password to connect to the WIFI hotspot.

Pi-5-details-pic106.png

HDMI display test

1) Use HDMI to HDMI cable to connect Orange Pi development board and HDMI display

Pi-5-details-pic107.png

2) After starting the linux system, if the HDMI monitor has image output, it means that the HDMI interface is working normally

Note that although many notebook computers have an HDMI interface, the HDMI interface of the notebook generally only has the output function, and does not have the function of HDMI in, that is to say, the HDMI output of other devices cannot be displayed on the notebook screen.

When you want to connect the HDMI of the development board to the HDMI port of the laptop, please make sure that your laptop supports the HDMI in function.

When the HDMI is not displayed, please check whether the HDMI cable is plugged in tightly. After confirming that there is no problem with the connection, you can change a different screen and try to see if it is displayed.

HDMI to VGA display test

1) First, you need to prepare the following accessories
a. HDMI to VGA Converter

Pi-5-details-pic108.png

b. A VGA cable

Pi-5-details-pic109.png

c. A monitor or TV that supports VGA interface

2) HDMI to VGA display test as shown below

Pi-5-details-pic110.png


When using HDMI to VGA display, the development board and the Linux system of the development board do not need to make any settings, only the HDMI interface of the development board can display normally. So if there is a problem with the test, please check whether there is a problem with the HDMI to VGA converter, VGA cable and monitor.

HDMI resolution setting method

1) First open Display in Settings

Pi-5-details-pic111.png

2) Then you can see the current resolution of the system

Pi-5-details-pic112.png

3) Click the drop-down box of Resolution to see all resolutions currently supported by the display

Pi-5-details-pic113.png

4) Then select the resolution you want to set, and click Apply

Pi-5-details-pic114.png

5) After the new resolution is set, select Keep the configuration

Pi-5-details-pic115.png

How to use Bluetooth

1.Test method of desktop image

1) Click the Bluetooth icon in the upper right corner of the desktop

Pi-5-details-pic116.png

2) Then select the adapter

Pi-5-details-pic117.png

3) If there is a prompt on the following interface, please select Yes

Pi-5-details-pic118.png

4) Then set the Visibility Setting to Always visible in the Bluetooth adapter setting interface, and then close it

Pi-5-details-pic119.png

5) Then open the configuration interface of the Bluetooth device

Pi-5-details-pic120.png

6) Click Search to start scanning the surrounding Bluetooth devices

Pi-5-details-pic121.png

7) Then select the Bluetooth device you want to connect to, and then click the right button of the mouse to pop up the operation interface of the Bluetooth device, select Pair to start pairing, and the demonstration here is to pair with an Android phone

Pi-5-details-pic122.png

8) When pairing, a pairing confirmation box will pop up in the upper right corner of the desktop, just select Confirm to confirm, and the phone also needs to confirm at this time

Pi-5-details-pic123.png

9) After pairing with the mobile phone, you can select the paired Bluetooth device, then right-click and select Send a File to start sending a picture to the mobile phone

Pi-5-details-pic124.png

10) The interface for sending pictures is as follows

Pi-5-details-pic125.png

USB interface test


The USB interface can be connected to a USB hub to expand the number of USB interfaces.

Connect USB mouse or keyboard to test

1) Insert the USB interface keyboard into the USB interface of the Orange Pi development board

2) Connect the Orange Pi development board to the HDMI display

3) If the mouse or keyboard can operate normally, it means that the USB interface is working normally (the mouse can only be used in the desktop version of the system)

Connect USB storage device test

1) First insert the U disk or USB mobile hard disk into the USB interface of the Orange Pi development board

2) Execute the following command, if you can see the output of sdX, it means that the U disk is recognized successfully

orangepi@orangepi:~$ cat /proc/partitions | grep "sd*"

3) Use the mount command to mount the U disk to /mnt, and then you can view the files in the U disk

orangepi@orangepi:~$ sudo mount /dev/sda1 /mnt/

orangepi@orangepi:~$ ls /mnt/
test.txt

The following command can be used to mount the U disk in exfat format on the Linux system

orangepi@orangepi:~$ sudo apt-get install exfat-utils exfat-fuse

orangepi@orangepi:~$ sudo mount -t exfat /dev/sda1 /mnt/

4) After mounting, you can view the capacity usage and mount point of the U disk through the df -h command

orangepi@orangepi:~$ df -h | grep "sd"
/dev/sda1 29G 208K 29G 1% /mnt

USB wireless network card test

The usable USB wireless network cards that have been tested so far are as follows. Please test other types of USB wireless network cards by yourself. If they cannot be used, you need to transplant the corresponding USB wireless network card driver.

serial number model
1 RTL8723BU
Support 2.4G WIFI+BT4.0 		Pi-5-details-pic126.png
2 RTL8811
Support 2.4G +5G WIFI 		Pi-5-details-pic127.png
3 RTL8821CU
Support 2.4G +5G WIFI
支持 BT 4.2 		Pi-5-details-pic128.png

1.RTL8723BU test

1) First insert the RTL8723BU wireless network card module into the USB interface of the development board

2) Then the linux system will automatically load the RTL8723BU bluetooth and WIFI-related kernel modules, through the lsmod command, you can see that the following kernel modules have been automatically loaded

orangepi@orangepi:~$ lsmod
Module Size Used by
rfcomm 57344 16
rtl8xxxu 106496 0
rtk_btusb 61440 0

3) Through the dmesg command, you can see the loading information of the RTL8723BU module

orangepi@orangepi:~$ dmesg

4) Then you can see the device node of RTL8723BU WIFI through the sudo ifconfig command. For the connection and test method of WIFI, please refer to the section of WIFI connection test, which will not be repeated here

orangepi@orangepi:~$ sudo ifconfig wlx0013eff458ae

wlx0013eff458ae: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:13:ef:f4:58:ae txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

5) Then you can see the USB Bluetooth device through the hciconfig command

orangepi@orangepi:~$ sudo apt update && sudo apt install bluez

orangepi@orangepi:~$ hciconfig
hci0: Type: Primary Bus: USB
BD Address: 00:13:EF:F4:58:AE ACL MTU: 820:8 SCO MTU: 255:16 DOWN
RX bytes:1252 acl:0 sco:0 events:125 errors:0
TX bytes:23307 acl:0 sco:0 commands:125 errors:0

6) You can also see the bluetooth icon on the desktop. At this time, the bluetooth is not turned on, so a red x will be displayed

Pi-5-details2-pic01.png

7) Click Turn Bluetooth On to turn on Bluetooth

Pi-5-details2-pic02.png

8) The display after turning on Bluetooth is as follows

Pi-5-details2-pic03.png

9) For the test method of Bluetooth, please refer to the section on Bluetooth usage, so I won’t go into details here

2.RTL8811 test

1) First insert the RTL8811 wireless network card module into the USB interface of the development board

2) Then the linux system will automatically load the kernel module related to RTL8811 WIFI, through the lsmod command, you can see that the following kernel module has been automatically loaded

orangepi@orangepi:~$ lsmod
Module Size Used by
8821cu 1839104 0

3) Through the dmesg command, you can see the loading information of the RTL8811 module

orangepi@orangepi:~$ dmesg

[ 118.618194] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 118.767152] usb 2-1: New USB device found, idVendor=0bda, idProduct=c811, bcdDevice= 2.00
[ 118.767181] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 118.767199] usb 2-1: Product: 802.11ac NIC
[ 118.767219] usb 2-1: Manufacturer: Realtek
[ 118.767235] usb 2-1: SerialNumber: 123456
[ 119.500530] usbcore: registered new interface driver rtl8821cu

4) Then, you can see the WIFI device node through the sudo ifconfig command. For the WIFI connection and test method, please refer to the WIFI connection test section, which will not be repeated here

orangepi@orangepi:~$ sudo ifconfig wlx1cbfced9d260

wlx1cbfced9d260: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 1c:bf:ce:d9:d2:60 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)

3.RTL8821CU test

1) First insert the rtl8821cu wireless network card module into the usb interface of the development board

2) Then use the lsusb command to see the device information of the rtl8821cu usb wifi module, please make sure that the USB module is not in Driver CDROM Mode

grep "Realtek"

Bus 002 Device 003: ID 0bda:c820 Realtek Semiconductor Corp. 802.11ac NIC

grep "Realtek"

Bus 002 Device 002: ID 0bda:1a2b Realtek Semiconductor Corp. RTL8188GU 802.11n WLAN Adapter (Driver CDROM Mode)

If the USB WIFI module seen by the lsusb command is in Driver CDROM Mode, please unplug the USB WIFI module again. If not, please manually execute the following command to switch to the next mode：

3) The linux system will automatically load the rtl8821cu bluetooth and wifi related kernel modules, through the lsmod command, you can see that the following kernel modules have been automatically loaded

orangepi@orangepi:~$ lsmod
Module Size Used by
8821cu 1839104 0
rtk_btusb 61440 0

4) Through the dmesg command, you can see the loading information of the rtl8821cu module

orangepi@orangepi:~$ dmesg

......
[ 57.083693] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 57.231888] usb 2-1: New USB device found, idVendor=0bda, idProduct=1a2b, bcdDevice= 2.00
[ 57.231916] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 57.231937] usb 2-1: Product: DISK
[ 57.242594] usb-storage 2-1:1.0: USB Mass Storage device detected [ 57.245674] scsi host0: usb-storage 2-1:1.0
[ 58.069172] usb 2-1: USB disconnect, device number 2
[ 58.440025] usb 2-1: new high-speed USB device number 3 using ehci-platform
[ 58.587819] usb 2-1: New USB device found, idVendor=0bda, idProduct=c820, bcdDevice= 2.00
[ 58.587827] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 58.587833] usb 2-1: Product: 802.11ac NIC
[ 58.587838] usb 2-1: Manufacturer: Realtek
[ 58.587844] usb 2-1: SerialNumber: 123456
[ 58.610463] rtk_btusb: Realtek Bluetooth USB driver ver 3.1.6d45ddf.20220519-142432
[ 58.610656] usbcore: registered new interface driver rtk_btusb
[ 58.634631] Bluetooth: hci0: RTL: examining hci_ver=08 hci_rev=000c lmp_ver=08 lmp_subver=8821
[ 58.636729] Bluetooth: hci0: RTL: rom_version status=0 version=1
[ 58.636740] Bluetooth: hci0: RTL: loading rtl_bt/rtl8821c_fw.bin
[ 58.664190] Bluetooth: hci0: RTL: loading rtl_bt/rtl8821c_config.bin
[ 58.664746] Bluetooth: hci0: RTL: cfg_sz 10, total sz 31990
[ 59.122471] Bluetooth: hci0: RTL: fw version 0x829a7644
[ 59.265513] usbcore: registered new interface driver rtl8821cu
[ 59.280119] rtl8821cu 2-1:1.2 wlx90de80521825: renamed from wlan0

5) Then you can see the device node of rtl8821cu wifi through the sudo ifconfig command. For the wifi connection and test method, please refer to the section of WIFI connection test, which will not be repeated here

orangepi@orangepi:~$ sudo ifconfig wlx90de80521825

wlx90de80521825: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:13:ef:f4:58:ae txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)

6) Then you can see the USB Bluetooth device through the hciconfig command

orangepi@orangepi:~$ sudo apt-get update && sudo apt-get install -y bluez

orangepi@orangepi:~$ hciconfig
hci0: Type: Primary Bus: USB
BD Address: 00:13:EF:F4:58:AE ACL MTU: 820:8 SCO MTU: 255:16 DOWN
RX bytes:1252 acl:0 sco:0 events:125 errors:0
TX bytes:23307 acl:0 sco:0 commands:125 errors:0

7) You can also see the bluetooth icon on the desktop. At this time, the bluetooth is not turned on, so a red x will be displayed

Pi-5-details2-pic04.png

8) Click Turn Bluetooth On to turn on Bluetooth

Pi-5-details2-pic05.png

9) The display after turning on Bluetooth is as follows

Pi-5-details2-pic06.png

10) For the test method of Bluetooth, please refer to the section on Bluetooth usage, so I won’t go into details here

USB camera test

1) First, you need to prepare a USB camera that supports UVC protocol as shown in the figure below or similar, and then insert the USB camera into the USB port of the Orange Pi development board

Pi-5-details2-pic07.png

2) Through the v4l2-ctl command, you can see that the device node information of the USB camera is /dev/video0

orangepi@orangepi:~$ v4l2-ctl --list-devices

Q8 HD Webcam: Q8 HD Webcam (usb-fc880000.usb-1):
/dev/video0
/dev/video1
/dev/media0

Note that the l in v4l2 is a lowercase letter l, not the number 1.

In addition, the serial number of the video is not necessarily video0, please refer to what you actually see.

3) In the desktop system, Cheese can be used to directly open the USB camera. The method of opening Cheese is shown in the figure below.：

Pi-5-details2-pic08.png

The interface after Cheese turns on the USB camera is shown in the figure below：

Pi-5-details2-pic09.png

4) Method of using fswebcam to test USB camera
a. Install fswebcam

orangepi@orangepi:~$ sudo apt update

orangepi@orangepi:~$ sudo apt-get install -y fswebcam

b. After installing fswebcam, you can use the following command to take pictures
a) -d option is used to specify the device node of the USB camera
b) --no-banner is used to remove the watermark of the photo
c) The -r option is used to specify the resolution of the photo
d) The -S option is used to set the number of previous frames to skip
e) ./image.jpg is used to set the name and path of the generated photo

orangepi@orangepi:~$ sudo fswebcam -d /dev/video0 \

--no-banner -r 1280x720 -S 5 ./image.jpg

c. In the server version of the linux system, you can use the scp command to transfer the taken pictures to the Ubuntu PC for image viewing after taking pictures

orangepi@orangepi:~$ scp image.jpg [email protected]:/home/test（ Modify the IP address and path according to the actual situation）

d. In the desktop version of the linux system, you can directly view the captured pictures through the HDMI display

Testing audio methods on desktop systems

1) First open the file manager

Pi-5-details2-pic10.png

2) Then find the following file (if there is no audio file in the system, you can upload an audio file to the system yourself)

Pi-5-details2-pic11.png

3) Then select the audio.wav file, right click and select open with vlc to start playing

Pi-5-details2-pic12.png

4) How to switch between different audio devices such as HDMI playback and headphone playback
a. First open the volume control interface

Pi-5-details2-pic13.png

b. When playing audio, the audio device options that the playback software can use will be displayed in Playback, as shown in the figure below, where you can set which audio device to play to

Pi-5-details2-pic14.png

The method of using commands to play audio

1.Headphone interface playback audio test

1) First insert the earphone into the earphone jack of the development board

Pi-5-details2-pic15.png

2) Then you can use the aplay -l command to view the sound card devices supported by the linux system. From the output below, we can see that card 2 is the sound card device of es8388, that is, the sound card device of the headset

orangepi@orangepi:~$ aplay -l
        • List of PLAYBACK Hardware Devices ****

card 0: rockchipdp0 [rockchip-dp0], device 0: rockchip-dp0 spdif-hifi-0 [rockchip-dp0 spdif-hifi-0] Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: rockchiphdmi0 [rockchip-hdmi0], device 0: rockchip-hdmi0 i2s-hifi-0 [rockchip-hdmi0 i2s-hifi-0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: rockchipes8388 [rockchip-es8388], device 0: dailink-multicodecs ES8323.6-0010-0 [dailink-multicodecs ES8323.6-0010-0]
Subdevices: 1/1

3) Then use the aplay command to play the audio file that comes with the system. If the earphone can hear the sound, it means that the hardware can be used normally.

rangepi@orangepi:~$ aplay -D hw:2,0 /usr/share/sounds/alsa/audio.wav

Playing WAVE 'audio.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo

2.HDMI audio playback test

1) First use the HDMI to HDMI cable to connect the Orange Pi development board to the TV (other HDMI monitors need to ensure that they can play audio)

2) Then check the serial number of the HDMI sound card. From the output below, you can know that the HDMI sound card is card 1

orangepi@orangepi:~$ aplay -l
        • List of PLAYBACK Hardware Devices ****

card 0: rockchipdp0 [rockchip-dp0], device 0: rockchip-dp0 spdif-hifi-0 [rockchip-dp0 spdif-hifi-0] Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: rockchiphdmi0 [rockchip-hdmi0], device 0: rockchip-hdmi0 i2s-hifi-0 [rockchip-hdmi0 i2s-hifi-0] Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: rockchipes8388 [rockchip-es8388], device 0: dailink-multicodecs ES8323.6-0010-0 [dailink-multicodecs

3) Then use the aplay command to play the audio file that comes with the system. If the HDMI monitor or TV can hear the sound, it means that the hardware can be used normally

orangepi@orangepi:~$ aplay -D hw:1,0 /usr/share/sounds/alsa/audio.wav

Method of using commands to test recording

1) There is an onboard MIC on the development board, the location is as follows：

Pi-5-details2-pic16.png

2) Running the test_record.sh main command will record a piece of audio through the onboard MIC, and then play it to HDMI and headphones

orangepi@orangepi:~$ test_record.sh main

Start recording: /tmp/test.wav
Recording WAVE '/tmp/test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo Start playing
Playing WAVE '/tmp/test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
Playing WAVE '/tmp/test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo

3) In addition to the onboard MIC, we can also record audio through headphones with MIC function. After inserting the headset with MIC function into the development board, run the test_record.sh headset command to record a piece of audio through the headset, and then play it to HDMI and the headset.

orangepi@orangepi:~$ test_record.sh headset

Start recording: /tmp/test.wav
Recording WAVE '/tmp/test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo Start playing
Playing WAVE '/tmp/test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
Playing WAVE '/tmp/test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo

26 Pin Interface Pin Description

1) Please refer to the figure below for the order of the 26 pin interface pins on the Orange Pi 5 development board

Pi-5-details2-pic17.png

2) The functions of the 26 pin interface pins on the Orange Pi 5 development board are shown in the table below
a. The following is the complete pin diagram of 26pin

Pi-5-details2-pic18.png

b. The table below is the picture of the left half of the complete table above, so you can see it clearly

Pi-5-details2-pic19.png

c. The table below is the picture of the right half of the complete table above, so you can see it clearly

Pi-5-details2-pic20.png


The pwm in the above table has marked the base address of the corresponding register, which is useful when checking which pwmchip in /sys/class/pwm/ corresponds to which pwm pin in the 26pin header.

3) There are a total of 17 GPIO ports in the 26pin interface, and the voltage of all GPIO ports is 3.3v

Instructions for the use of the android 12 system

How to use the use of wireless network card

1) At present, the USB wireless network card model that is adapted to the image is shown below：

Chip model Function VID&PID Adaptation
RTL8821CU 2.4G +5G WIFI+BT 4.2 0bda:c820 Only support wifi, Bluetooth needs to be adapted
RTL8723BU 2.4G WIFI+BT4.0 0bda:b720 Only support wifi, Bluetooth needs to be adapted
RTL8811CU 2.4G +5G WIFI 0bda:c811 Only WIFI function, supported

2) The picture of the above three USB wireless network cards is shown below：
a. The picture of the RTL8821CU USB wireless network card module is shown below：

Pi-5-details2-pic21.png

b. The pictures of the RTL8723BU USB wireless network card module are shown below：

Pi-5-details2-pic22.png

c. The picture of the RTL8811CU USB wireless network card module is shown below：

Pi-5-details2-pic23.png

3) The test methods of the USB wireless network cards of the above 3 models are the same. First, insert the USB network card into the USB interface of the development board, and then enter Setting

Pi-5-details2-pic24.png

4) Then choose Network & internet

Pi-5-details2-pic25.png

5) Then choose Internet

Pi-5-details2-pic26.png

6) Then turn on the Wi-Fi switch

Pi-5-details2-pic27.png

7) If everything is normal after opening the Wi-Fi, you can scan to the nearby Wi-Fi hotspot

Pi-5-details2-pic28.png

8) Then select the Wi-Fi you want to connect, and you will pop up the password input interface shown in the figure below

Pi-5-details2-pic29.png

9) Then use the keyboard to enter the corresponding password of the wi-fi, and then use the mouse to click the Enter button in the virtual keyboard to start connecting Wi-Fi

Pi-5-details2-pic30.png

10) The display after the Wi-Fi connection is successful as shown in the figure below：

Pi-5-details2-pic31.png

26pin GPIO port test

1) First click the Wiringop icon to open the Wiringop App

Pi-5-details2-pic32.png

2) The main interface of the Wiringop app is displayed as shown in the figure below, and then click the GPIO_TEST button to open the GPIO test interface

Pi-5-details2-pic33.png

3) The GPIO test interface is shown in the figure below. The two rows of the CheckBox button on the left and the 26PIN pin are one -to -one relationship. When checking the CheckBox button, the corresponding pin will be set to OUT mode, the pin level settings will be set. For high levels, when the check -up is canceled, the pin level is set to a low level; when clicking the GPIO READALL button on the right, you can get the WPI, GPIO mode, pin level information, etc.

Pi-5-details2-pic34.png

4) Then click the GPIO READALL button, and the output information is shown in the figure below

Pi-5-details2-pic35.png

5) Taking the high and low level of the GPIO2_D4 as an example, click the CheckBox button in the figure below. When the button is selected, the GPIO2_D4 is set to a high level. After setting, you can use the value of the voltage of the pins by the multimeter. If it is 3.3v, Explain that setting high -electricity is successful

Pi-5-details2-pic36.png

6) Then click the GPIO READALL button to see that the pins mode of the current GPIO2_D4 is OUT, and the pin level is high level

Pi-5-details2-pic37.png

7) Click the CheckBox button in the figure below to cancel the check status. The GPIO2_D4 pin is set to a low level. After setting, you can use the value of the voltage of the multimeter to measure the pins.If it is 0v, the low -power flat is set.

Pi-5-details2-pic38.png

8) Then click the GPIO READALL button to see that the pins mode of the current GPIO2_D4 is OUT, and the pin level is low

Pi-5-details2-pic39.png

26pin UART test

1) In Android default, the UART0 serial port is only opened. The position of UART0 at 26pin is shown in the figure below. The corresponding device node is/dev/ttys0

Pi-5-details2-pic40.png

2) First click the WiringOP icon to open the Wiringop App

Pi-5-details2-pic41.png

3) The main interface of the WiringOP APP is displayed as shown in the figure below, and then click the UART_TEST button to open the UART test interface

Pi-5-details2-pic42.png

4) The serial test interface of the APP is shown in the figure below

Pi-5-details2-pic43.png

5) Then enter the baud rate you want to set in the editing box, and then click the OPEN button to open the /dev/ttyS0 node. After successful, the OPEN button becomes an optional state.The CLOSE button and the SEND button become an optional state

Pi-5-details2-pic44.png

6) Then use the DuPont line to shorte the RXD and TXD pin of uart0

Pi-5-details2-pic45.png

7) Then you can enter a section of characters in the editing box below, click the SEND button to start sending

Pi-5-details2-pic46.png

8) If everything is normal, the receiving string will be displayed in the receiving box

Pi-5-details2-pic47.png

26pin's PWM test

1) Android only opened PWM15 by default. The corresponding pins are at the position of 26Pin.

Pi-5-details2-pic48.png

2) First click theWiringOP icon to open the Wiringop App

Pi-5-details2-pic49.png

3) Then click the PWM_TEST button to enter the PWM test interface at the main interface of WiringOP

Pi-5-details2-pic50.png

4) The corresponding address corresponding to the PWM15 is febf0030. The right side of PWMCHIP0 is exactly the febf0030.pwm. If the displayed base address is wrong, please click the drop -down option to select other PWMCHIP until the febf0030 is displayed on the right.

Pi-5-details2-pic51.png

5) Then confirm the PWM cycle. The default configuration is 50000ns, and the PWM frequency is 20KHz. You can modify it by yourself.Click on the button to export PWM15

Pi-5-details2-pic52.png

6) Then drag the drag below to change the PWM duty ratio, and then check the enable to output PWM

Pi-5-details2-pic53.png

Pi-5-details2-pic54.png

26pin's SPI test

1) From the schematic diagram of the 26pin interface, the SPI available for Orange Pi 5 is spi4

Pi-5-details2-pic55.png

2) Here is the w25q64 module to test the SPI interface, and first access the w25q64 device at the SPI4 interface.

Pi-5-details2-pic56.png

3) Then click the WiringOP icon to open the WiringOP APP

Pi-5-details2-pic57.png

4) The main interface of the WiringOP APP shows as shown in the figure below, click the SPI_TEST button to open the SPI test interface

Pi-5-details2-pic58.png

5) Then click the OPEN button to initialize SPI

Pi-5-details2-pic59.png

6) Then fill in bytes that need to be sent, such as reading the ID information of W25Q64, fill in the address 0x9F in data [0], and then click the TRANSFER button

Pi-5-details2-pic60.png

7) The last app will display the ID information read

Pi-5-details2-pic61.png

8) The MANUFACTURER ID of the w25q64 module is EFh, the Device ID is 4017h, and the value read above is corresponding (H represents hexadecimal)

Pi-5-details2-pic62.png

Retrieved from "http://www.orangepi.online/orangepiwiki/index.php?title=Orange_Pi_5_detail&oldid=2191"